GiantShark RC

What electric motor would be equivilent to a 46 ic

Tboi159 I am using the 3530 -3536 range of motors on 3s with 300 watts of power with 40a esc works well

such a pod, if previous person requesting item contacts me fine if not it will go on general sale .

Hi am new member notice that back in october someone asked about Voodo fibreglass fuselage for plan RO80 Having cleared roof out guess what have

Guess this doesn't get used all that often...?

Hi, i am an aerospace engineering student, and we have been set a challenge to build an aircraft model. We carried out a constraints analysis, and we found out that the model will weigh about 2kg and we need a motor that will produce about 280 watts of power during climb. I was wondering if anyone had any suggestions on which motor will be the most suitable for this project. thanks

Would you know if any word on coverting a ESR to test a 1 s pack?

Happy new year folks.... 1st Dec 2013 Robin hood **Tue Jan 01, 2013 10:04 am**

Happy new year folks.... 1st Dec 2013

I've joined in the RCM&E Model Flyer Forum 2013 Mass Build, which is based on the Nigel Hawes Tucano 45". I've decided to use the XYH435-42 1250kv motor and Hobbywing Pentium 60A ESC. I ordered these on line with 2xGens Ace 3000 25C Lipos, propellers and other odds and ends on 26 December and they've arrived today, all exactly as ordered. Thank you Giant Shark, I can get on with the project now.

Just to wish all the shark workers and customers a happy christmas and a crash free new year regards twinkle

Hi,just like my other orders from Giantcod ,am very pleased with the great reliable delivery and items ordered. Mick41

still going on. appears to be soldered to the pcb without strain relief. I think i'll do something about this myself before installation (without tampering with the product to any great extent. thats it for now.

bit more regarding design (mechanical) heat shrink case a bit flimsy, bit nurvious at pressing and holding the body whilst connecting battery and servos. Ther aerial is very thin and does not appear to be secured against strain/flexing very well.

lets start again corona rp6d1. bit of a problem in getting it into the locking mode. found that if you hold the button to enter into set up for longer than 2 secs is better but still its down to timing. locked onto five frequiencies ok including 81 and 83.

Hi first time buy from giantshark, first time to this forum. have bought a corona rp6d1. good service received Rx quickly good .

hi chaps, can anyone recommend a 100w to 120w brushless motor for a 36" model low wing plane? thanks

Hi folks, I have a Multiplex Magister and want to covert it to brushless, what do I need?

Further delving into the Forum revealed what I needed to know and made the conversion of my Robbe F-14 much easier than I thought possible.

Hoping to convert My Robbe F14 Navy to 2.4 with FRSky hack module. Pos and neg connections look easy but where is the PPM connection? anyone got any photos please of a completed conversion/ thanks

My 1st post. I have would like to know where the Antenna for a Corona RS41011 R/C Reciever attaches as mine has broken off the PCB board. Thank you. Rab

hi there,this is my first post on here and im looking for knowledge on home made planes and wing loadings. i have built a 30" balsa plane withe the view of doing some 3d with any luck. the plane has 255sq in of wing area and weight is 20.45 oz which gives me a wing loading of11.55 ozsqft, can anyone tell me if this weight and wing area will be capable of flying 3d? it is fitted with a overlander thumper t2836/08 with a 10x5 prop pulling270 watts. any help would be very welcome

Hi can u help. I make and fly vintage high wing planes and have just finished my new plane. This planes is my third electric. The WT is 2 1/2 pounds with a wingspan of 60 inches. I have purchased (these were recomended) a motor and speed controller the motor is an EMAX GT2812/10 I have tried a 12x4 and an10x8 prop but if will not get off the ground it seems that if it had 18000 in stead of10600 it would get off the ground. WHAT DO I NEED?

Just bought 2 x 2.4Ghz 8ch Corona Receiver (DSSS) V2 following a long wait including screw-ups by PayPal and have sucessfully converted my JR PCM9 to 2.4 GHz operation at reasonable cost. Just hope that the 8channel receivers will remain in stock so I can replace all 35 and 40 MHz receivers in my boats and planes.

i recently bought some Towerpro MG90 servo's, put them in my heli and now everything is reversed,they seem to be reversed,i hooked another type of servo up and the travel was normal,but when i hook the MG90 up it goes the other way,wot is wrong, i thought all servo's all travelled the same way,i can correct this by reversing the switche's on the tx,but cant reverse the aux 1,it bugger's everything up any idea's guy's

Could you please update your 'phone number on (contact us part of the) website.

GiantShark RC

Giantshark Chat Center

Who is online